pandaoffer75

Peugeot 208 Key Replacement Peugeot 208 key replacement is best left to experienced auto locksmiths with the right equipment and technical know-how. They can design and program keys more quickly and at a lower cost than dealers. If the key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are other reasons why the key may be malfunctioning. Dead Coin Battery A dead coin battery can hinder your Peugeot 208 from locking or unlocking, and will not allow you to start the engine. In this case you'll have to employ the alternate method of starting that is described in the owner's manual. Another reason why your 208 might not start is that the spark plugs have been worn down. The spark plugs ignite fuel to start the engine. They have a limited life span. If they are not used enough they will eventually fail. There is a simple solution for this issue. Examine the voltage of your battery using a multimeter. If it's lower than 11.5 Volts and you are not satisfied, then it is time to replace it. If the battery has corrosion it is essential to clean its contacts. This can be accomplished by removing the rubber covers off the two battery terminals, and then using a wirebrush, you can remove any corroded parts of the battery. Then, you should reconnect the positive and negative pole cables. Water Damage If your 208 doesn't start and the battery hasn't been replaced, you must inspect the spark plugs. It could be that they're dirty and they don't spark. This can be easily corrected by cleaning the spark plugs in the workshop. Peugeot automobiles use keys that are transponder-type and works with the car's immobiliser system. This ensures only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it will not transmit the proper signal to the vehicle. This is a typical issue that is often caused by water damage. This is a common issue in warmer climates where the vehicle is exposed to snow or rain. In this situation, contact a reputable locksmith who will have the required tools and equipment to reprogram the key. They will also have the latest technological know-how and machinery required to create a Peugeot 208 smart key. The process shouldn't take more than 15 minutes. Contacts with the battery may be damaged. Peugeot changed from the old carbon-encased transponder chips to a new type of chip that relies on electronic components that are placed on a circuit board. This new system works great when it's fresh, however, over time, the circuit boards begin to wear out and stop functioning correctly. This can prevent the immobiliser's function from being activated, meaning the vehicle won't start. Contact an Peugeot specialist, or a locksmith if this is the case. A common problem is when the battery of the key fob begins to die. This causes the blade of the key to stop feeding into your lock. A locksmith for cars can replace the battery and cut a new blade for you, it's usually a simple fix. Faulty Receiver Module It could be that the receiver module is faulty If your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer that regulates the central locking system of your Peugeot vehicle. Rubber seals on the key fob keep water from getting to the electronic chip. The chip can be damaged by water in the event that it is exposed water for long periods of period of. Submerging the key fob in sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content. The module must be replaced if your Peugeot spare key does not work anymore. This can only be done by a Peugeot specialist or an expert auto locksmith. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the right coding for the start of the engine. This is the reason that you should only rely on the Peugeot locksmith to design and program the replacement. Faulty On-Board Computer The on-board computer of your Peugeot is responsible for many of the systems in your car, including airbags and power windows. When something goes wrong in these systems, they will usually display a code indicating the problem. This code will be saved in the system until the issue is fixed. In most cases, this will require replacing the computer on board. One of the most frequent reasons for the airbag light turning on is loose or corroded connection in the airbag sensor. This can be caused by wear and tear, age or exposure to moisture and salt. This issue should be dealt with as soon as you can, because an airbag that is malfunctioning could pose danger in the event of an accident. If you find an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob may be weak or dead. This will prevent the key fob from sending a signal to disable the immobilizer on your vehicle's standard. You can test this by pressing the unlock button on the key fob and then trying to start your car. If G28 fails, then the key battery needs to be replaced.